There's no debate – when you choose Crown's XTi 2 Series, you're choosing one of the most powerful and innovative amplifiers on the market today. That's because the all-new XTi 2 Series amps continue to set the standard for unmatched performance and value, delivering the goods night after night without breaking a sweat.
Peakx Plus™ Limiters provide the ultimate in system performance and protection by allowing full control over threshold, attack, and release
Enhanced Subharmonic Synth section provides user control over frequency, gain and filter type for system-specific tuning
3 User-defined fan mode controls – normal, early and fullspeed – for matching fan performance to a specific application
New system monitoring provides software visibility of AC line voltage and power supply temperature
Integrated cast-aluminum handles for easy handling and enhanced durability
Locking power cord clip provides a secure connection between the amplifier and power cord
Updated HiQnet System Architect™ control software
Increased number of presets to a total of 50; 49 of which are user definable
6 parametric filters per channel with adjustable Q, ±15 dB boost/cut. Also adjustable high and low shelving filters. This 8-filter EQ section can be bypassed.
Highpass and Lowpass per channel. Butterworth 6/12/18/24 dB per octave. Linkwitz-Riley 24/48 dB per Octave. Also includes ± 15 dB bandpass gain and polarity control.
8 parametric filters per channel with adjustable Q, ±15 dB boost/cut. This 8-filter EQ section can be bypassed.
For signal alignment of driver; 50 mS of total delay.
Takes the low-frequency content of the input signal and "synthesizes" a new signal that is the same as the input signal but one octave lower. The new synthesized signal is then mixed with the original signal to create the effect. New: Users now have control over frequency, gain, and filter type.
Peakx™ Plus Limiter
User defeatable limiter that allows users to control Threshold, Attack, and Release times.
50 total presets, 49 of which are user-definable.
Sensitivity (for full rated power at 4 ohms)
Frequency Response (at 1 watt, 20 Hz - 20 kHz)
+0 dB, –1 dB
Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms)
XTi1002/2002/4002: 100 dB (A weighted)
XTi6002: 103 dB (A weighted)
Total Harmonic Distortion (THD)
Damping Factor 20 Hz to 1 kHz
Crosstalk (below rated power)
20 kHz - 1 kHz: > 70 db
Input Impedance (nominal)
20k ohms balanced, 10k ohms unbalanced
Maximum Input Signal
+22 dBu typical
AC Line Voltage and Frequency Configurations
100 VAC, 120 VAC, 220-240 VAC 50/60 Hz
AC Line Current
(120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch)
XTi1002: 6.8A; no more than 38W at idle
XTi2002: 8.3A; no more than 38W at idle
XTi4002: 10.5A; no more than 38W at idle
XTi6002: 15.3A; no more than 180W at idle
0°C to 40°C at 95% relative humidity (non-condensing)
Two front-panel rotary level controls, one for each channel
On/Off switch applies AC power to the amplifier
Three buttons near the LCD screen that are used to access menu items and front panel lockout
Backlit liquid crystal display that shows preset and processing status
Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
Green LED flashes when output signal exceeds -10 dB below clip.
Green LED flashes when output signal level exceeds -20 dB below clip.
Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
Red LED, one per channel, turns on at the threshold of audible distortion
Red LED, one per channel, illuminates under excessive temperature conditions
Blue LED illuminates when the amplifier has been turned on and has power
XLR, one per channel
Loop-thru signal from input connector for linking another amplifier, one per channel.
Two Neutrik® Speakon® NL4MP output connectors. Channel-1 Speakon® is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).
HiQnet™ USB Connector
Type B, connects to HiQnet™ network.
Proportional speed fan with front-to-rear airflow.
XTi 1002/2002/4002: 19" (W) x 3.5" (H) x 12.25" (D)
XTi 6002: 19" (W) x 3.5" (H) x 16.2" (D)
XTi 1002/2002/4002: 18.5 lbs (8.4kg)
XTi 6002: 24.0 lbs (10.9kg)
XTi 1002/2002/4002: 21.5 lbs (9.8kg)
XTi 6002: 30.0 lbs (13.6kg)
XTi 1002 XTi 2002 XTi 4002 XTi 6002
2Ω Stereo (per ch.) 700W 1000W 1600W 3000W
4Ω Stereo (per ch.) 500W 800W 1200W 2100W
8Ω Stereo (per ch.) 275W 475W 650W 1200W
8Ω Bridge-Mono 1000W 1600W 2400W 4200W
4Ω Bridge-Mono 1400W 2000W 3200W 6000W